Shaker 1000 to Avic F90BT
+2
07Shelby500
03.sonicblue
6 posters
Page 1 of 2
Page 1 of 2 • 1, 2
Shaker 1000 to Avic F90BT
Has anyone installed an AVIC F series to their Shaker 1000 factory subs/speakers. I have wired everything with the correspondence with David (Mineral Grey). But I am very concerned because I have two wiring harness that were sent to me (Bought:http://cgi.ebay.com/2007-Ford-Mustang-Radio-Wiring-Harness-Shaker-1000_W0QQitemZ230141323802QQcmdZViewItemQQptZCar_Electronics_Installation), but the factory has three. One is for your usual hook ups: dimmer, speaker, power, etc. Another is for the two subs and the amps (which I get popping when car comes on). But what is the third one for, any ideas. I am looking to finish the install tonight if I can get a 12 volt to 5 volt regulator to hopefully stop the bad pop as the amps come on, everything is wired except the sirius which will be done too. But wanted to see if anyone here has done the shaker 1000 wiring for an after market stereo.
Thanks all
Thanks all
Guest- Guest
03.sonicblue- BMMC Board Member
- Number of posts : 5734
Age : 42
Location : Broken Arrow
Car Type : 03 Mustang Cobra
First Name : Jerry
Registration date : 2008-07-26
Re: Shaker 1000 to Avic F90BT
Does the Radio work?? other than the poping, do the subs works and the other speakers??
03.sonicblue- BMMC Board Member
- Number of posts : 5734
Age : 42
Location : Broken Arrow
Car Type : 03 Mustang Cobra
First Name : Jerry
Registration date : 2008-07-26
Re: Shaker 1000 to Avic F90BT
Have to hook it up again tonight to make 100% sure, but the sub was working the front and rear 6X8's were working, can not remeber if the subs in the door were.
Guest- Guest
Re: Shaker 1000 to Avic F90BT
I dont think it goes to anything....I believe mine is disconnected
Guest- Guest
Re: Shaker 1000 to Avic F90BT
Jarrod can you give him the link to the writeup we looked at when we installed your AVIC system and the little dealy majigger that we installed to keep it from popping.
07Shelby500- BMMC Board Member
- Number of posts : 9044
Age : 48
Location : Owasso Oklahoma
Car Type : The thing which must not be spoken of
First Name : David
Registration date : 2008-03-10
Re: Shaker 1000 to Avic F90BT
My AVIC F90 is installed with the exception of the AM and FM channels (waiting for an adapter). Would like to thank Jerry, Jarrod, Justin, and Brad for helping get the regulator on. Have really not got to play with it yet, but Jerry and Jarrod did and they seemed to love it. Was a late night but hell of fun. "No Jarrod you can not have any of my apple pie!" Thanks again guys. Also would like to thank my wife for feeding us some of her homemade cookies, to keep Jarrod focused.
Guest- Guest
Re: Shaker 1000 to Avic F90BT
Wanted to thank David (Mineral Grey) for helping with the bypass and showing me his F90 so I would get the itch to buy one. HAHA. Thanks again for your correspondence back and forth.
Guest- Guest
Re: Shaker 1000 to Avic F90BT
No problem, Michael! Glad yours is in and working. Let me know if you'd like help in connecting the VSS, and/or if you want a tutorial in how to boot your F90 into Windows CE test mode, ruin a couple of critical operating files, and turn it into a very expensive paperweight.
Metric7- BMMC Veteran Member
- Number of posts : 2258
Age : 46
Location : Tulsa
Car Type : Jeep. That's right, I said Jeep. Deal with it.
First Name : David
Registration date : 2008-03-12
Re: Shaker 1000 to Avic F90BT
I will get a good test on the VSS tomorrow on the way to work, but when I drove a little bit yesterday it kept up with me.
Guest- Guest
Re: Shaker 1000 to Avic F90BT
What your seeing could be just the GPS accuracy - there's not even a way to verify the VSS signal is hooked up correctly on the F90. Like I've said, though, there's lots of folks (on avic411.com) that haven't connected the VSS on their F90s and accuracy didn't seem to suffer.
Metric7- BMMC Veteran Member
- Number of posts : 2258
Age : 46
Location : Tulsa
Car Type : Jeep. That's right, I said Jeep. Deal with it.
First Name : David
Registration date : 2008-03-12
Re: Shaker 1000 to Avic F90BT
Does the F90 have the speed, Gforce, performance readings like the D3 does?
Guest- Guest
Re: Shaker 1000 to Avic F90BT
The deck is sweet! If you have an iphone, this is the one to get, the d series does not let you upload your phone book. It worked like a champ on Mikes, not to mention the voice dial. Very Cool.
03.sonicblue- BMMC Board Member
- Number of posts : 5734
Age : 42
Location : Broken Arrow
Car Type : 03 Mustang Cobra
First Name : Jerry
Registration date : 2008-07-26
Re: Shaker 1000 to Avic F90BT
Grabber07' wrote:Does the F90 have the speed, Gforce, performance readings like the D3 does?
No, it doesn't. I kind of miss that screen, too.
Metric7- BMMC Veteran Member
- Number of posts : 2258
Age : 46
Location : Tulsa
Car Type : Jeep. That's right, I said Jeep. Deal with it.
First Name : David
Registration date : 2008-03-12
Re: Shaker 1000 to Avic F90BT
03.sonicblue wrote:The deck is sweet! If you have an iphone, this is the one to get, the d series does not let you upload your phone book. It worked like a champ on Mikes, not to mention the voice dial. Very Cool.
Uploading (and then voice dial) differs greatly by phone on the F90 - it works perfectly with some phones; others, not so much. But, the gurus on avic411.com figured out how to download the F90's phone data file (after it pairs with your phone), then how to restructure the file and load it back on the F90 - solves all the problems inherent with the phones that don't work on the first try!
Metric7- BMMC Veteran Member
- Number of posts : 2258
Age : 46
Location : Tulsa
Car Type : Jeep. That's right, I said Jeep. Deal with it.
First Name : David
Registration date : 2008-03-12
Re: Shaker 1000 to Avic F90BT
Yeah I love it. Just got to use it on the way to work today. Everything seems to be working great right now. I was reading on the VSS with the F90 all it is basically used for is the sound volume as you go faster it automatically turns up. But I could be wrong.
Guest- Guest
Re: Shaker 1000 to Avic F90BT
groupset wrote:03.sonicblue wrote:The deck is sweet! If you have an iphone, this is the one to get, the d series does not let you upload your phone book. It worked like a champ on Mikes, not to mention the voice dial. Very Cool.
Uploading (and then voice dial) differs greatly by phone on the F90 - it works perfectly with some phones; others, not so much. But, the gurus on avic411.com figured out how to download the F90's phone data file (after it pairs with your phone), then how to restructure the file and load it back on the F90 - solves all the problems inherent with the phones that don't work on the first try!
Is there a way to do that on the D series. Seems there has always been a problem with the d series and the iphone. Is there every any software updates you can download for these radios, or is the Bluetooth a hardware issue?? seems to have been a lot of back and forth on that topic.
03.sonicblue- BMMC Board Member
- Number of posts : 5734
Age : 42
Location : Broken Arrow
Car Type : 03 Mustang Cobra
First Name : Jerry
Registration date : 2008-07-26
Re: Shaker 1000 to Avic F90BT
I'm afraid there's no similar fix for the D-series. The Bluetooth in the D-series is all Pioneer hardware (thus the separate BT box) driven by fixed firmware in the D. Starting with the F-series, Pioneer began using Parrot hardware (chips) and software for the BT functioning. You can update BT software on the F-series via the USB connection (I've done so once already); plus it just works smoother out of the box than the D-series BT ever did. And, because the F-series is Windows CE based, that's what allows you to go in and pull the phonebook data file and make any required fixes - can't do that on the non-Windows based D-series.
Note to the J-twins (Jerry and Jarrod) - if you boys ever decide to man up and get an F-series unit, your existing D-3 harness works perfect with the F! All you have to is change the mute pin position for bypass purposes on the F (it's in a different location on the harness than what the D uses), and plug it in to the F-series!
Note to the J-twins (Jerry and Jarrod) - if you boys ever decide to man up and get an F-series unit, your existing D-3 harness works perfect with the F! All you have to is change the mute pin position for bypass purposes on the F (it's in a different location on the harness than what the D uses), and plug it in to the F-series!
Metric7- BMMC Veteran Member
- Number of posts : 2258
Age : 46
Location : Tulsa
Car Type : Jeep. That's right, I said Jeep. Deal with it.
First Name : David
Registration date : 2008-03-12
Re: Shaker 1000 to Avic F90BT
I will just wait for you to upgrade to the next one,
I would have to un install the BT and XM, because the old one would go into the mustang and the F series would go in the truck. Would be a lot of work, but the thought has crossed my mind.
I would have to un install the BT and XM, because the old one would go into the mustang and the F series would go in the truck. Would be a lot of work, but the thought has crossed my mind.
03.sonicblue- BMMC Board Member
- Number of posts : 5734
Age : 42
Location : Broken Arrow
Car Type : 03 Mustang Cobra
First Name : Jerry
Registration date : 2008-07-26
Re: Shaker 1000 to Avic F90BT
You said you just got your Tax refund.
Go for it, got mine off of 6th AVE (http://www.6ave.com) for 598.00 using coupon AFLPIO598. That way I did not have to worry about e-bay. might even be able to find it cheaper.
Go for it, got mine off of 6th AVE (http://www.6ave.com) for 598.00 using coupon AFLPIO598. That way I did not have to worry about e-bay. might even be able to find it cheaper.
Guest- Guest
Re: Shaker 1000 to Avic F90BT
Never mind two days late Jerry. Sure you can find it somewhere else though.
Guest- Guest
Re: Shaker 1000 to Avic F90BT
03.sonicblue wrote:I will just wait for you to upgrade to the next one,
Ha! You're closer to the truth than you realize...I'm what marketing people refer to as an "early adapter" - gotta have the new electronic toys as soon as they come out!
Metric7- BMMC Veteran Member
- Number of posts : 2258
Age : 46
Location : Tulsa
Car Type : Jeep. That's right, I said Jeep. Deal with it.
First Name : David
Registration date : 2008-03-12
Re: Shaker 1000 to Avic F90BT
Mikeyd3113 wrote:Never mind two days late Jerry. Sure you can find it somewhere else though.
Damn, two days late and $500 short.
03.sonicblue- BMMC Board Member
- Number of posts : 5734
Age : 42
Location : Broken Arrow
Car Type : 03 Mustang Cobra
First Name : Jerry
Registration date : 2008-07-26
Re: Shaker 1000 to Avic F90BT
I'll sell you mine for $1,099.00, Jerry. Already bypassed and everything.
Metric7- BMMC Veteran Member
- Number of posts : 2258
Age : 46
Location : Tulsa
Car Type : Jeep. That's right, I said Jeep. Deal with it.
First Name : David
Registration date : 2008-03-12
Re: Shaker 1000 to Avic F90BT
mmmm, NO!!
Hey david, how do I get the XM icons to display, some channels display but most dont. Is there a way to get them all to display??
Hey david, how do I get the XM icons to display, some channels display but most dont. Is there a way to get them all to display??
03.sonicblue- BMMC Board Member
- Number of posts : 5734
Age : 42
Location : Broken Arrow
Car Type : 03 Mustang Cobra
First Name : Jerry
Registration date : 2008-07-26
Re: Shaker 1000 to Avic F90BT
Probably not on your antique D3, Jerry. Subsequent to the XM/Sirius merger, a lot of the icons and station IDs (names) changed. I don't think there's a means to update the D-series icons and logos, but you might check the XM thread on avic411.com. I downloaded a file off that thread and have updated the icons, etc. on my F90. Just another reason for you to make the leap into 21st century technology! I want more than anyone for you to do that, so today only I'll sell you my F90 for $1,025.00.
Metric7- BMMC Veteran Member
- Number of posts : 2258
Age : 46
Location : Tulsa
Car Type : Jeep. That's right, I said Jeep. Deal with it.
First Name : David
Registration date : 2008-03-12
Re: Shaker 1000 to Avic F90BT
the price is very tempting. Would you be willing to wager it over a friendly game of bowling??
03.sonicblue- BMMC Board Member
- Number of posts : 5734
Age : 42
Location : Broken Arrow
Car Type : 03 Mustang Cobra
First Name : Jerry
Registration date : 2008-07-26
Re: Shaker 1000 to Avic F90BT
I might - I now have my own custom ball and shoes and have been practicing.
Metric7- BMMC Veteran Member
- Number of posts : 2258
Age : 46
Location : Tulsa
Car Type : Jeep. That's right, I said Jeep. Deal with it.
First Name : David
Registration date : 2008-03-12
Page 1 of 2 • 1, 2
Similar topics
» Pioneer AVIC-X920BT GPS/XM/DVD/AM/FM Double-Din Head Unit
» Pioneer AVIC-D3 With Bluetooth, Ipod Cable, Remote, and East & West DVDs
» Super Shaker is On....
» cdc shaker kit
» I have $1000.00, what are my options guys?
» Pioneer AVIC-D3 With Bluetooth, Ipod Cable, Remote, and East & West DVDs
» Super Shaker is On....
» cdc shaker kit
» I have $1000.00, what are my options guys?
Page 1 of 2
Permissions in this forum:
You cannot reply to topics in this forum
|
|
8/18/2015, 3:30 pm by coolhandluke
» Upholsetry work - black door panel
6/16/2015, 10:20 pm by mystang2007
» 347CI Dart Iron Eagle complete engine for sale, drop in and go fast!
6/25/2014, 6:07 pm by ruger311
» 7 Quarts AMSOIL Synthetic, AMSOIL Filter, Stock Brake Pads, Misc items
4/11/2014, 1:51 pm by Corepuncher
» shelbyfest?
4/9/2014, 2:37 am by Vandy9303
» tko 600 Swap 1965 mustang
4/2/2014, 12:18 pm by tulsadrags
» WTB five or six speed transmission
3/21/2014, 10:06 am by tulsadrags
» 03 cobra chrome wheels and new tires asking 600.00
3/17/2014, 9:14 am by tulsadrags
» spring cruise
12/21/2013, 10:06 pm by Captain Chaos
» BMMC GT/CS Registry
11/26/2013, 11:00 pm by gcmustanglx