Bold Moves Mustang Club of Tulsa
Would you like to react to this message? Create an account in a few clicks or log in to continue.
Log in

I forgot my password

Latest topics
» For Sale: 2009 Ford Mustang Shelby GT 500
Programming a Ford PATS key. Empty8/18/2015, 3:30 pm by coolhandluke

» Upholsetry work - black door panel
Programming a Ford PATS key. Empty6/16/2015, 10:20 pm by mystang2007

» 347CI Dart Iron Eagle complete engine for sale, drop in and go fast!
Programming a Ford PATS key. Empty6/25/2014, 6:07 pm by ruger311

» 7 Quarts AMSOIL Synthetic, AMSOIL Filter, Stock Brake Pads, Misc items
Programming a Ford PATS key. Empty4/11/2014, 1:51 pm by Corepuncher

» shelbyfest?
Programming a Ford PATS key. Empty4/9/2014, 2:37 am by Vandy9303

» tko 600 Swap 1965 mustang
Programming a Ford PATS key. Empty4/2/2014, 12:18 pm by tulsadrags

» WTB five or six speed transmission
Programming a Ford PATS key. Empty3/21/2014, 10:06 am by tulsadrags

» 03 cobra chrome wheels and new tires asking 600.00
Programming a Ford PATS key. Empty3/17/2014, 9:14 am by tulsadrags

» spring cruise
Programming a Ford PATS key. Empty12/21/2013, 10:06 pm by Captain Chaos

» BMMC GT/CS Registry
Programming a Ford PATS key. Empty11/26/2013, 11:00 pm by gcmustanglx

Poll
March 2024
SunMonTueWedThuFriSat
     12
3456789
10111213141516
17181920212223
24252627282930
31      

Calendar Calendar

Sponsors

Programming a Ford PATS key.

Go down

Programming a Ford PATS key. Empty Programming a Ford PATS key.

Post by Guest 9/2/2008, 9:29 am

Thought this was pretty cool info if anyone is needing a second key or has lost their key.

Pretains to the following vehicles
Ford Contour ‘98–up
F-150 ‘98-up
Ford Crown Victoria ’97-up
Ford Escort 99-up
Ford Excursion ‘00-up
Ford Expedition ‘98–up
Ford Explorer ’98-up
Ford Focus ‘00-up
Ford Mustang ’96-up
Ford Ranger ’98-up
Ford Taurus ’96-up
Ford Windstar ’98-up
Lincoln Continental ’98-up
Lincoln LS ’00-up
Lincoln Mark VIII ’98-up
Lincoln Navigator ’98-up
Lincoln Town Car ’98-up
Mercury Grand Marquis ’97-up
Mercury Mountaineer ’98-up
Mercury Mystique ’98-up
Mercury Sable ’96-up


On-Board Programming Method "B"

for Ford keys (1996 -early 1998 Ford, Lincoln, Mercury)

If you want to initiate a new master key....




1. Insert new key into ignition cylinder and turn it to the ON (RUN) position. The security light on the dash will flash for fifteen minutes.
2. When the security light stops flashing, you have FIVE minutes to start the next step. Turn the ignition cylinder OFF and then back to the ON (RUN) position. The security light on the dash will flash for fifteen more minutes.
3. When the security light stops flashing, you have FIVE minutes to start the next step. Turn the ignition cylinder to OFF and then back ON (RUN) position. The dash will flash for fifteen more minutes.
4. After the security light stops flashing the third time, the new key has been programmed into the vehicles computer and will operate the car. It has replaced ALL the previous electronic key codes and is the ONLY key programmed into the vehicles computer.
If you want to add a key....



1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within 15 seconds, insert the new key and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming the key into the vehicle.
5. Don't attempt to start the vehicle with any key for at least 1 minute.



On-Board Programming Method "C"


for Ford keys (Later 1998-newer Ford, Lincoln, Mercury)

If you want to initiate a new master key....

1. This requires that the vehicle be connected to special dealer equipment. There are two ten minute delays involved while this device erases all existing key programming and sets up the vehicle computer to accept new key codes. Two new keys should be ready because the system requires a minimum of two keys in the program. After the first two keys are programmed, additional keys can be entered individually by following the instructions for adding duplicate keys (below).
If you want to add a key....



**You must have two original keys to perform this procedure. If you only have one key, you WILL have to take it to the dealer to get it programmed**
1. Insert and existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (RUN) and back to OFF. Ignition should stay on for at least ONE SECOND.
3. Remove the existing key and, within TEN seconds, insert a second working key and turn it to ON (RUN) and the back OFF. Ignition must be in ON for at least ONE second, but no more than TEN seconds. Remove the key.
4. Insert the new key before TWENTY seconds have elapsed and turn it to ON (RUN). Leave it the ON position for at least ONE second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate that the new key has been successfully programmed.
6. To program additional keys, repeat steps 1 through 5


Last edited by BlackGT02 on 9/2/2008, 9:49 am; edited 1 time in total

Guest
Guest


Back to top Go down

Programming a Ford PATS key. Empty Re: Programming a Ford PATS key.

Post by 07Shelby500 9/2/2008, 9:48 am

Interesting. Now if they just sold those damn things at your local key center.
07Shelby500
07Shelby500
BMMC Board Member
BMMC Board Member

Number of posts : 9044
Age : 48
Location : Owasso Oklahoma
Car Type : The thing which must not be spoken of
First Name : David
Registration date : 2008-03-10

Back to top Go down

Programming a Ford PATS key. Empty Re: Programming a Ford PATS key.

Post by Guest 9/2/2008, 9:49 am

lol.. Ebay is about the best place to find real Ford logo'd ones without paying out the ass for them.

Guest
Guest


Back to top Go down

Programming a Ford PATS key. Empty Re: Programming a Ford PATS key.

Post by 07Shelby500 9/2/2008, 9:52 am

Brilliant!
07Shelby500
07Shelby500
BMMC Board Member
BMMC Board Member

Number of posts : 9044
Age : 48
Location : Owasso Oklahoma
Car Type : The thing which must not be spoken of
First Name : David
Registration date : 2008-03-10

Back to top Go down

Programming a Ford PATS key. Empty Re: Programming a Ford PATS key.

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum